FoamCoat™

FoamCoat is a non-toxic, water-based coating for styrofoam and polystyrene foam, as well as other surfaces. It provides a hard, durable finish that resists chipping and cracking, yet can be sanded smooth or carved to add detailing. FoamCoat can be used on a wide variety of surfaces including foam, primed wood, concrete block, primed fiberglass, papier mâché, muslin and many other materials. FoamCoat is fully compatible with all Rosco Scenic Paints used either as colorants or as surface coatings. FoamCoat is flame retardant and water resistant.

Application: Apply by brush, roller, or hopper spray gun depending on the desired finish. The thickness of the coating is determined by the application. When coating over fine details, use successive thin coats to build up a protective layer without obscuring the details. For an extra smooth finish without sanding, smooth the coated surface with a wet sponge before the FoamCoat™ has set completely.

Suggested Use: Excellent for use as a protective coating for many types of foam projects. Especially useful on foam scenery or props that receive physical abuse or need to last for extended tours. It can also be used as a texturing agent that is more durable and not as brittle as plaster or joint compound.

Surface Preparation:

  • Foam: All surfaces should be clean and dry, free of dust and grease before application.
  • Wood & Plastic: Clean and prime surface with Rosco Tough Prime before applying FoamCoat™.
  • For particularly difficult materials, lightly sand surface to give it more "tooth" before applying FoamCoat™.

 

Compatibility: FoamCoat™ is compatible with most water-based coatings and is easily painted or tinted. Tint FoamCoat™ using Supersaturated Roscopaint or a colorant like Proline, Mixol, Universal or Cal Tints. It is not necessary to prime FoamCoat™ before painting.

Mixing: Stir well. Due to the weight of the solids in FoamCoat™ settling may occur. Use a power mixing blade for best results.

Dilution: Use FoamCoat™ undiluted for most durable single coat application. FoamCoat™ may be diluted with water if desired. Thinner mixtures will flow and level more than an undiluted application and will dry to a thinner coating.

Color: Off-white, matte finish.

Coverage: Varies with application. Approximately 150 sq. ft. per gallon (14 sq. m. per 3.79L).

Film Thickness: Varies with application. 1/16" - 3/16" per application.

Dry Time: Varies with thickness of coating. Approximately 2-8 hours. Allow 24 hours to be completely dry to the touch.

Clean-Up: Soap and water.

Shelf Life: Minimum 24 months.

Packaging: 1 Gallon and 3 1/2 Gallon (3.79L and 13.26L)

CAUTIONS: Do not apply when surface or air temperatures are below 50°F (10°C). Keep from freezing. Avoid prolonged contact with skin or breathing of spray. Do not take internally. Use adequate ventilation. KEEP OUT OF REACH OF CHILDREN.

All technical data, recommendations and service are accurate to the best of our knowledge. Rosco assumes no responsibility for the results obtained or damage incurred from use by the buyer in whole or in part since method of application and its use is beyond our control.

Product Number

150 07100 0128

FoamCoat™ - Gallon

150 07100 0448

FoamCoat™ - 3 1/2 Gallon

FoamCoat™ Data Sheet

FoamCoat™ - GHS SDS

FoamCoat™ - SDS

The Rosco Guide to Scenic Finishes

Creating Textured Surfaces

Case Study: How to Create Durable, Vibrant, and Water-Resistant Halloween Décor

Case Study: Use This FoamCoat Technique To Create Your Next Sculpture

Case Study: Priming Techniques For Foam Carving Using Rosco FoamCoat and CrystalGel